Platinum Stock Products; High temperature, low profile, industrial, ceramic shear ICP® accel., 100 mV/g, 0.8 to 8000 Hz, side exit, 2-pin connector, single point ISO 17025 accredited calibration
- Sensitivity: (±10%) 100 mV/g(10.2 mV/(m/s²))
- Frequency Range: (±3dB) 48 to 480000 cpm(0.8 to 8000 Hz)
- Sensing Element: Ceramic
- Measurement Range: ±50 g(±490 m/s²)
- Weight: 5.4 oz(153 gm)
Very high temperature low noise PFA cable, 2-conductor, twisted pair, shielded, xx-ft, 2-socket, 400°F, 7/16-27 UNS-2B plug to 2-socket, high temp. MS3106 conn. w/strain relief (meets MIL-C-5015)
Very high temperature low noise PFA cable, 2-conductor, twisted pair, shielded, xx-ft, 2-socket, 400°F, 7/16-27 UNS-2B plug to 2-pin, MS3101A connector w/strain relief (meets MIL-C-5015)
High temperature, low profile, industrial, ceramic shear ICP® accel., 100 mV/g, 0.8 to 8000 Hz, side exit, integral cable, single point ISO 17025 accredited calibration
- Sensitivity: (±10%) 100 mV/g(10.2 mV/(m/s²))
- Frequency Range: (±3dB) 48 to 480000 cpm(0.8 to 8000 Hz)
- Sensing Element: Ceramic
- Measurement Range: ±50 g(±490 m/s²)
- Weight: (without cable) 5.4 oz(153 gm)
Polyurethane cables feature a braided shield and are ideal for indoor or outdoor general purpose applications.
PCB accelerometers and pressure cryogenic sensors are designed and tested to promote survivability in demanding environments.
-320°F (-196°C). It can be exposed to much lower temperatures to -420°F (-251°C), indicated as a storage temperature specification. To survive at these lower temperatures, specially selected amplifier components are used along with each unit being hermetically sealed and indivi
BNC connectors are ideal to terminate cables used with single-axis ICP accelerometers and vibration transmitters
PCB® high temperature dynamic pressure sensors are designed for operation up to +1400 ºF
Impact-style sensors are specifically designed for impact force measurements.
CSI data collector for your handheld data collector needs
PCB 261 Series 3-Component Quartz Force Links for measuring high frequency dynamic force
Armored cables and connectors for industrial sensors
Cables classified as high-temp can be used with high-temp ICP accelerometers and charge mode sensors in applications above 250 deg F (121 deg C).
BreakAway Connectors for portable data collection
Discover IMI Sensors’ advanced charge amplifiers for charge mode accelerometers and pressure sensors.
Endevco cryogenic charge output piezoelectric accelerometers are built specifically to measure vibration under conditions down to -452° F (-269° C).
PTFE cables slide easily through cable trays and will survive in acidic environments when paired with the right connector.
900°F (482°C) with stud mount
357A64: Up to 1200°F (649°C) with screw tab mount
357M168: Up to 1200°F (649°C) with weld tab mount
Features of the UHT-12 sensing element:
Proprietary crystal technology sealed in a hermetic package provides long-term relia
Instrumentation for Extreme Temperature Environments Designed to withstand application challenges of extreme heat environments such as gas turbines.
General purpose force sensors are offered in either stud or axial mounted configurations.
In-line ICP® charge converters serve to convert high impedance charge mode piezoelectric sensor signals to low impedance voltage signals.
Cryogenic cables and connectors
4-socket MIL connectors mate with most industrial ICP accelerometers
PCB high temperature accelerometers allow for measurements up to 1200ºF
PCB® Quartz ICP® force rings are used to measure compression and tension.
IMI offers a full line of industrial cable assemblies as well as bulk cable spools and field installable 2-pin MIL connectors.
PCB quartz ICP® force rings measure dynamic compression.
PCB quartz ICP® force link sensors measure dynamic compression and tension.
PCB Miniature Quartz Force Sensors give reliable data at a Low Amplitude level.
Charge mode pressure sensors can withstand continuous temperatures up to 1200°F, making them ideal for on-turbine pressure monitoring.
Enhance your industrial data collection with IMI’s rugged cable connectors, compatible with DLI, Rockwell (Entek), and CSI handheld devices.
Individual connector specifications and photos.
Simplify the connection between an ICP® accelerometer to a third-party data collector with an industrial data collector cable.
PCB 260 Series 3-Component Quartz Force Rings for measuring high frequency dynamic force
1200°F (650°C) Introducing PCB's Model 176A07 June 13, 2023 DEPEW, NY - PCB Piezotronics (PCB®) is introducing our new Model 176A07, UHT-12TM High Temperature Pressure Sensor. The 176A07 is a UHT-12 hazardous area approved design with a temperature rating of 1200°F (650&
662°F (-240 to 350°C).
Model 112A06 features:
UHT-12TM sensing element for more accurate, lower noise measurements at elevated temperatures
Wide temperature range from -400°F to 662°F (-240°C to 350°C)
Resonant frequency >200 kHz
Hi
Discover PCB Piezotronics' range of externally polarized 1/2 inch microphones for precise acoustics measurement.
Explore PCB Piezotronics' specialty probe microphones for specialized acoustics measurement applications.
400 °F
(760 °C) without Need for Water Cooling
June 15, 2021, Depew, NY – PCB Piezotronics, Inc. today announced the release of a new ultra-high temperature pressure sensor for combustion testing and thermoacoustic pressure measurements with a unique design element that eliminates the
Explore IMI’s field-installable connectors, built for premium performance in virtually all harsh industrial conditions.
Instrumentation for High Temperature Environments
Accelerometers and pressure sensors for demanding measurement & monitoring requirements
IMI Sensors provides reliable, high-temperature dynamic pressure and vibration measurement to detect combustion instability in modern gas turbines.
PCB manufactures accelerometers and vibration sensors for testing and research applications.
Both an impact and overall vibration transmitter the RMP is designed to capture mechanical looseness and cracked rods in reciprocating machinery.
Optimized for the unique challenges of protecting and monitoring reciprocating machinery.
Accessories for mounting PCB® pressure sensors.
Discover PCB Piezotronics' range of prepolarized 1/2 inch microphones for precise acoustics measurement.
eries 176 high-temperature pressure sensors (986F, 530C) are directly mounted at the gas turbine combustor. The brochure also includes IMI's full line of high-temperature accelerometers for vibration monitoring of gas turbines in heat environments of up to +1200°F (+649°C).
Please d
PCB® manufactures pressure sensors for a variety of dynamic pressure measurements.
900 °F (482 °C) Environments
July 20, 2016, Depew, New York - PCB Piezotronics announced the release of Model 357A100, a new high temperature differential charge accelerometer with a UHT-12™ sensing element. This accelerometer is for use during gas turbine engine research and testing and
PCB Sensors measure dynamic combustion instability pressures in intense heat flow associated with high temperature rocket motor environments.
Cryogenic ICP® accelerometers from IMI Sensors are designed for exceptional performance in harsh, low-temperature environments down to -320 °F.
400 °F (760 °C) without Need for Water Cooling
October 20, 2023, Depew, NY - PCB Piezotronics, Inc. today announced the release of a new ultra-high temperature pressure sensor for combustion testing and thermoacoustic pressure measurements with a unique design element that
2-socket MIL connectors mate with most industrial ICP accelerometers
356 °F, with a full temperature range of -65 to 356 °F (-54 to 180 °C).
The sensing elements provide a 5 mV/g output over a 2 to 8K Hz frequency range and are hermetically sealed in a rugged, scratch-resistant, titanium housing. With an overall cube size of just 0.28 inches (7.1 mm)
PCB’s high-precision accelerometers and other test sensors have been relied upon for decades to provide maximum safety and comfort in rail transport.
3-socket MIL connectors mate with most industrial ICP accelerometers
900°F (482°C). Vibration monitoring of gas turbines provides critical information to diagnose potential problems, leading to an increase in uptime and decrease in unplanned maintenance, catastrophic failures and accidents. The new high temperature EX600B13 sensors feature one piece cons
With a wide variety of acoustic sensors in-stock, PCB has helped many companies conduct precise measurement of their acoustic tests.
500°F (260°C).
Model 357A67 features:
Small size 0.78 x 0.40 x 0.45 in (19.8 x 10.2 x 11.4 mm)
High charge output 3.0 pC/g
High resonant frequency ≥ 45 kHz
Measurement range ±1,000 g
Model 357A67 is PCB's first charge output accelerometer that util
PCB series 3711F, 3713F, 3741F, and 3743G high performance VC MEMS accelerometers for low frequency measurements down to zero hertz.
PCB cryogenic pressure sensors ensure reliable operation and accurate measurements in extremely cold environments.
1200°F Accelerometer Eliminates Noise
UHT-12™ Crystals have Better Accuracy and Higher Temperature Capability
UHT-12™ PCB Hardware
March, 4 2015, Depew, N.Y. - PCB Piezotronics, Inc., is pleased to announce a new crystal technology being used in high temperature applications, called Ultra Hi
500°F (260°C). The 422E5x series features five gain options allowing greater compatibility with a wide range of sensors, and comes in a small, rugged package. These charge converters also offer a less expensive alternative when compared to laboratory charge amplifiers, which makes them at
+325°F/+163°C can be tolerated. The sensing element of these accelerometers provides a sensitivity of (±10%) 100 mV/g (10.2 mV/(m/s²)) with a frequency range of (±3dB) 30 to 480000 cpm (0.5 to 8000 Hz).
This sensor can be used as drop-in replacement for existing accelerom
When developing headphones and earbuds, certain safety testing has to be performed. Be sure to use PCB sensors for your product testing.
Explore PCB Piezotronics' specialty high-temperature microphones for precise acoustics measurement in extreme environments.
PCB’s acoustic products are used by manufacturers of power tools, audio equipment, and a wide array of consumer electronics.
PCB offers a wide range of sensors for testing in both extreme cold and heat to match the environments faced by heavy equipment and off-highway vehicles.
PCB High Temperature Charge Mode accelerometer can operate up to 1200°F/+649ºC. (certain models).
Discover PCB Piezotronics' specialty high-amplitude pressure microphones for advanced acoustics measurement.
200° F (-54 to 93° C) and a frequency response from 0.4 to 5000 Hz. These features make them ideal for flight testing, ground vibration testing, and environmental stress screening.
Built-in ICP® microelectronics provide a low noise, low impedance output signal capable of signal tra
IMI offers a complete line of dynamic pressure sensors for industrial applications.
PCB miniature accelerometers satisfy complex measurement needs in a small size.
Endevco’s piezoresistive silicon pressure sensors (8500 series) offer accurate and reliable performance at pressure extremes.
Measure high pressure, repetitive pulses in hydraulic & pneumatic applications
EX378B02 PCB prepolarized condenser mic is approved for hazardous locations, safe in gaseous environments where standard mics pose fire risk.
200 °F/
649 °C), differential output, charge accelerometers with a UHT-12™ sensing element and integral hardline cable terminating in a 7/16-27 2-pin connector. Model 357A94 has an axis of measurement parallel to the direction of the mounting screw while Model 357A95 has an axis of measur
+325°F (163°C). These features make them ideal for small component testing, environmental stress screening, and impact testing of electronic board assemblies.
Built-in ICP® microelectronics provide a low noise, low impedance output signal for low transmission loss over long distance
250 °F (-73 to +121 °C) and excellent resolution. It features a measurement range of 3,000 psi (20,685 kPa) with a maximum pressure of 5,000 psi (34,475 kPa). Integrated ICP® electronics inside Model 123B22 have a low impedance voltage output capable of being transmitted over long cab
200 °F Accelerometers to High Temperature Portfolio
Provides Better Accuracy and Higher Temperature Capability for Gas Turbine and Automotive Applications
June 19, 2005 Depew, New York - PCB Piezotronics, Inc., is pleased to announce two new accelerometers, Models 357D92 and 35793, that make me
(-20° C < Ta < 70° C)
Last week, IMI also announced the Class I, Division 2 certification from CSA for EchoPlus® Wireless Junction box. When combined with IMI’s hazardous area approved sensors, such as model EX603C01, the EchoPlus® Wireless Junction Box model CS672A01 i
(-20° C < Ta < 70° C)
When combined with IMI’s hazardous area approved sensors, such as model EX603C01, the EchoPlus® Wireless Junction Box model CS672A01 is ideal for the monitoring of rotating equipment in Oil & Gas refining and processing applications.
The wireless
300 °F (704 °C) in an industrial housing. The unit comes standard with a 10 foot (3 meter) integral hard-line cable terminating in a LEMO® connector, but other cable lengths and terminating connectors are available (2-pin 7/16-27).
In addition to warranty, pricing, lead time, as we
Adhesive and magnetic bases for mounting PCB accelerometers.
-320°F (-196°C). It is the first triaxial accelerometer to complement PCB's 351 family of single axis cryogenic accelerometers.
Model 354A14 features:
Wide frequency range up to 10k Hz at 10%
High resonant frequency of ≥ 25 kHz
Small size and low mass
Hazardous area approved vibration transmitters approved for use in hazardous areas
PCB Piezotronics delivers world-class accelerometers, microphones, and accessories for NVH testing in electric and hybrid vehicles.
Torque transducers that meet measurement requirements in the areas of automotive, aerospace, R&D, and process control.
Explore our specialized sensors for monitoring cryogenic pump systems across key industries.
Discover PCB's rugged microphones designed for reliable performance in harsh environments.
325 °F (-73 to +163 °C). Model 320C52 has a frequency range from 1 to 10 kHz (+/- 5%) and Model 320C53 has a frequency range from 1 to 5,000 Hz (+/- 5%). A single pole low pass filter, with a corner frequency set to ≥20 kHz, is incorporated into each model which reduces the potential for
325 °F/66-163 °C).
Choice of Measurement Range: In order to provide a measurement range that corresponds to the application's requirements, the electronic switch can be factory-set to one of the following five options: 0 to 1.5 ips peak velocity, 0 to 3.0 ips peak velocity, 0 to 5
PCB manufactures a wide variety of general purpose ICP® and charge mode piezoelectric accelerometers with measurement in three orthogonal directions.
Endevco’s piezoresistive blast pressure sensors (8500 series) have fast response times to measure blast waves
+93 °C (0 to 200 °F).
Endevco piezoresistive pressure sensors feature a unique silicon diaphragm design, which produces an extremely high output signal and high resonant frequency. These sensors have extraordinary linearity and repeatability with virtually no hysteresis.
For mo
+105°C (-40 to 221°F)
Model 7330 has full scale angular rate ranges including ±100, ±500, ±1500, ±6000, ±8000, ±12000 and ±18000 deg/sec, and provides full scale voltage output of ±2V. Designed for automotive rollover
PCB® manufactures sensors used for consumer electronics testing and component validation worldwide. Explore sensors for consumer electronics testing here.
When every second counts, accurate analysis of each component of your motorsport vehicle is essential. Make PCB test sensors a part of your winning team!
Discover PCB Piezotronics' dust and water-resistant specialty microphones for reliable acoustics measurement in challenging environments.
Discover PCB Piezotronics' side-vented pressure specialty microphones for accurate acoustics measurement.
140 °F
Choice of manual plunger‐style reset button or remote reset coil
Approval for use in hazardous areas*
For all technical inquiries and application support, please contact Victor Viola at vviola@pcb.com or 716-684-0002 x2491.
A
900 °F), charge output accelerometer with a UHT-12™ sensing element. This product, which features a miniature size, caseisolated housing, was developed for use in aviation/power generation, turbine research & development and automotive powertrain NVH applications.
The new UHT-12™ crystal t
250 °F temperatures and survives accidental
shock inputs to ±5,000 g.
Model 352A74 is available for immediate shipment. For additional information, visit
pcb.com/SensorsforTestMeasurement/Accelerometers/MiniaturePiezoelectric/SingleAxis/352A7X or contact Mike Lindstrom, PCB® Product
, and 176 Pressure Sensors
Series EX686, 685 Vibration Switches
Series EX682 Charge Amplifiers
The TR CU Compliance Certificate is issued by an independent accredited body through several laboratory quality tests of IMI’s product. This institution laboratory performs testing or ensures pro
800°C, which is much greater than traditional test and measurement microphones. This new design allows for sound pressure and resonant frequencies to be quantified for exhaust noise and engine analysis via a non-contact sensor on the automobile.
The probe tip diameter is extremely small, mea
f 70°C; a faster and more reliable Sierra Wireless LS300 Gateway for internet access; and improved component organization for ergonomics.
250 °F.
Model RTD602D91 is designed with a side exit, M12 connector, while model RTD602D11 contains a side exit, integral polyurethane cable of configurable lengths. Both designs are ideal for machine health monitoring in wind turbines, hydroelectric power plan
Learn about the characteristics and design of charge mode accelerometers.
PCB® single and triaxial ICP® accelerometers designed with a low temperature coefficient and wide operating temperature range.
PCB® series 113B dynamic pressure sensors set the standard for extremely fast, micro-second response with a wide amplitude and frequency range.
PCB high sensitivity pressure sensors are ideal for measuring small dynamic hydraulic and pneumatic pressures such as turbulence, noise, sound, and pulsations
+200° F (da -54 a +93° C) e un limite di sovraccarico da urto di ±5.000 g pk."L'isolamento del case aiuta a garantire la fedeltà delle misure in presenza di disturbi elettrici che si incontrano tipicamente durante le prove di vibrazione dei veicoli elettrici", ha di
Industrial Sensors for installations at elevated temperatures.
High Temperature Charge Accelerometers (to 1200 ºF / 650 ºC)
PCB low outgassing accelerometers include mini-triaxial, shock, and high temperature options for multiple aerospace applications.
248 °F (120 °C). Two-part epoxies offer stiffness, which maintains high-frequency response and a permanent mount. Depending on the application, adhesives such as dental cement, hot glues, instant glues, and duct putty can be viable options.
One adhesive isn't opti
PCB® manufactures accurate and reliable single and triaxial, ICP® accelerometers for motorsport testing applications
IMI Sensors offers radiation-hardened charge output accelerometers for nuclear applications. Engineered for extreme accuracy in high-temperature environments.
High Temperature ICP® Accelerometers that allow for measurements in environments up to +356ºF/+180ºC.
MEMS stands for micro electro mechanical system and applies to any sensor manufactured using microelectronic fabrication techniques.
250 °F (121 °C). Consult a PCB Applications Engineer to discuss testing requirements in higher temperature environments. 5.) Most ICP ® sensors have an all-welded hermetic housing. However, due to certain design parameters, certain models are epoxy sealed. In such cases, high humidity
400°F (204°C).
When considering the use of charge mode systems, remember that the output from the crystals is a pure electrostatic charge. The internal components of the force sensor and the external electrical connector maintain a very high (typically 10el3 ohm) insulation resistanc
Find a distributor or sales office.