Low power, industrial ICP® accel, 100 mV/g, 1.5 to 10k Hz, side exit, low profile with swiveler base, 10-ft integral cable, single point ISO 17025 accredited calibration
- Sensitivity: (±20%)100 mV/g
(10.2 mV/(m/s²))
- Frequency Range: (±3dB)90 to 600000 cpm
(1.5 to 10000 Hz)
- Sensing Element: Ceramic
- Measurement Range: ±50 g
(±490 m/s²)
- Weight: 1.1 oz
(31 gm)
|
English: |
SI: |
|
Performance |
Sensitivity (±20 %) |
100 mV/g |
10.2 mV/(m/s²) |
[1]
|
Measurement Range (12 VDC) |
±50 g |
±490 m/s² |
[3]
|
Measurement Range (5 VDC) |
±15 g |
±147 m/s² |
[3]
|
Frequency Range (±3 dB) |
90 to 600000 cpm |
1.5 to 10000 Hz |
|
Resonant Frequency |
1500 kcpm |
25 kHz |
[3]
|
Broadband Resolution (1) |
2 mg |
19.6 mm/s² |
[3]
|
Non-Linearity |
±1 % |
±1 % |
[2]
|
Transverse Sensitivity |
≤7 % |
≤7 % |
|
Environmental |
Overload Limit (Shock) |
5000 g pk |
49050 m/s² pk |
|
Temperature Range |
-65 to +250 °F |
-54 to +121 °C |
|
Temperature Response |
See Graph %/°F |
See Graph %/°F |
[3]
|
Enclosure Rating |
IP68 |
IP68 |
|
Electrical |
Settling Time (within 1% of bias) |
≤5.0 sec |
≤5.0 sec |
|
Discharge Time Constant |
≥0.1 sec |
≥0.1 sec |
|
Excitation Voltage |
5 to 12 VDC |
5 to 12 VDC |
|
Output Impedance |
<100 Ohm |
<100 Ohm |
|
Current Draw |
0.5 mA |
0.5 mA |
|
Output Bias Voltage |
2.5 to 6 VDC |
2.5 to 6 VDC |
|
Spectral Noise (10 Hz) |
18 µg/√Hz |
176.6 (µm/sec2)/√Hz |
[3]
|
Spectral Noise (100 Hz) |
4 µg/√Hz |
39.2 (µm/sec2)/√Hz |
[3]
|
Spectral Noise (1 kHz) |
2 µg/√Hz |
19.6 (µm/sec2)/√Hz |
[3]
|
Electrical Isolation (Case) |
>100000000 Ohm |
>100000000 Ohm |
|
Physical |
Size - Hex |
9/16 in |
14 mm |
|
Size - Height |
0.97 in |
24.6 mm |
|
Weight (without cable) |
1.1 oz |
31 gm |
[7]
|
Mounting |
Stud |
Stud |
|
Mounting Thread |
1/4-28 Male |
No Metric Equivalent |
[4]
|
Mounting Torque (Stud) |
7 to 8 ft-lb |
9.5 to 10.8 Nm |
[5]
[6]
|
Mounting Torque (hex nut) |
2 to 5 ft-lb |
2.7 to 6.8 Nm |
|
Sensing Element |
Ceramic |
Ceramic |
|
Sensing Geometry |
Shear |
Shear |
|
Housing Material |
Stainless Steel |
Stainless Steel |
|
Sealing |
Welded Hermetic |
Welded Hermetic |
|
Electrical Connector |
Molded Integral Cable |
Molded Integral Cable |
|
Electrical Connection Position |
Side |
Side |
|
Cable Termination |
Blunt cut |
Blunt cut |
|
Electrical Connections (Red) |
Pos (+) Power |
Pos (+) Power |
|
Electrical Connections (Black) |
Ground |
Ground |
|
Electrical Connections (White) |
Acceleration Output |
Acceleration Output |
|
Cable Length |
10 ft |
3.0 m |
|
Cable Type |
Polyurethane |
Polyurethane |
|
* All specifications are at room temperature unless otherwise specified
.


Specification Notes
[1] Conversion Factor 1g = 9.81 m/s².
[2] Zero-based, least-squares, straight line method.
[3] Typical.
[4] 1/4-28 has no equivalent in S.I. units.
[5] Stud torque must exceed sensor hex nut torque to ensure proper dismantling.
[6] 1/8" hex Allen key required for English version, 4 mm hex Allen key required for Metric version.
[7] Measured with mounting stud.
[8] See PCB Declaration of Conformance PS107 for details.
Accessories
|
|
|
Supplied |
080A156 |
Swivel mounting stud, 1/2-20 to 1/4-28 stud with 1/8" hex socket for installation (for models 607A11 & 607A61) |
1 |
ICS-2 |
Calibration of industrial accel., single-point, 100 Hz reference sensitivity |
1 |
Optional Versions
( M ) Metric Mount
Accessories: |
Supplied |
M080A159 |
Swivel Mounting Stud |
0 |