Model : 102B10 | ICP® Pressure Sensor

Click for lead times
cryogenic icp® pressure sensor, 100 psi, 50 mv/psi, 3/8-24 mtg thd, ground isolated with safety wire holes
$ 3,195.00 USD
(Pricing valid in US only!)

Cryogenic ICP® pressure sensor, 100 psi, 50 mV/psi, 3/8-24 mtg thd, ground isolated with safety wire holes

  • Measurement Range: 100 psi ( 690 kPa)
  • Sensitivity: (±15%)50 mV/psi ( 7.25 mV/kPa)
  • Low Frequency Response: (-5%)0.50 Hz
  • Resonant Frequency: >=250 kHz ( >=250 kHz)
  • Electrical Connector: 10-32 Coaxial Jack
  • Weight: 0.388 oz ( 11.00 gm)
English: SI:
Performance
Measurement Range (for ±5V output) 100 psi 690 kPa
Useful Overrange (for ± 10V output) 200 psi 1380 kPa [ 4]
Sensitivity (±15 %) 50 mV/psi 7.25 mV/kPa
Maximum Pressure (step) 1000 psi 6900 kPa
Maximum Pressure (Total) 15 kpsi 103425 kPa [ 3]
Resolution 2 mpsi 0.014 kPa [ 2]
Resonant Frequency ≥250 kHz ≥250 kHz
Rise Time (Reflected) ≤2.0 µ sec ≤2.0 µ sec
Low Frequency Response (-5 %) 0.50 Hz 0.50 Hz
Non-Linearity ≤1.0 % FS ≤1.0 % FS [ 1]
Environmental
Acceleration Sensitivity ≤0.002 psi/g ≤0.0014 kPa/(m/s²)
Temperature Range (Operating) -320 to +212 °F -196 to +100 °C
Temperature Coefficient of Sensitivity ≤0.06 %/°F ≤0.108 %/°C
Maximum Shock 20000 g pk 196133 m/s² pk
Electrical
Output Polarity (Positive Pressure) Positive Positive
Discharge Time Constant (at room temp) ≥1.0 sec ≥1.0 sec
Excitation Voltage 20 to 30 VDC 20 to 30 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance <100 Ohm <100 Ohm
Output Bias Voltage 8 to 14 VDC 8 to 14 VDC
Physical
Sensing Element Quartz Quartz
Housing Material 304L/316L Stainless Steel 304L/316L Stainless Steel
Thread Adaptor Material 316L Stainless Steel 316L Stainless Steel
Diaphragm 316L Stainless Steel 316L Stainless Steel
Sealing Welded Hermetic Welded Hermetic
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Weight 0.388 oz 11.00 gm
* All specifications are at room temperature unless otherwise specified
.




Specification Notes


[ 1] Zero-based, least-squares, straight line method.
[ 2] Typical.
[ 3] Due to high sensitivity, the static pressure should be applied and removed very slowly. Rate should prevent more than 10 Volt change in output until Output Bias Voltage returns to normal (approximately 15 times discharge time constant).
[ 4] Excitation voltage >=28 volts required.
[ 5] See PCB Declaration of Conformance PS023 for details.


Accessories


Supplied
065A44 Seal ring, 0.435" OD x 0.377" ID x 0.030" thk, Cu (for Model 102A10) 3


Optional Versions


( M ) Metric Mount
Accessories:
Supplied 065A34 Seal ring 0.435" OD x 0.397" ID x 0.030" Cu 3