Model : 102A44 | ICP® Pressure Sensor

Call for lead time
intrinsic safe icp® pressure sensor, 50 psi, 100 mv/psi, ground isolated, 10-32 connector, temp to 250f
$ 1,885.00 USD
(Pricing valid in US only!)

Intrinsic safe ICP® pressure sensor, 50 psi, 100 mV/psi, ground isolated, 10-32 connector, temp to 250F

  • Measurement Range: 50 psi ( 344.8 kPa)
  • Sensitivity: (±15%)100 mV/psi ( 14.503 mV/kPa)
  • Low Frequency Response: (-5%)0.5 Hz
  • Resonant Frequency: >=250 kHz ( >=250 kHz)
  • Electrical Connector: 10-32 Coaxial Jack
  • Weight: 0.6 oz ( 17.0 gm)
English: SI:
Performance
Measurement Range (for ±5V output) 50 psi 344.8 kPa
Sensitivity (±15 %) 100 mV/psi 14.503 mV/kPa
Maximum Pressure 4 kpsi 27580 kPa [ 2]
Resolution 0.001 psi 0.0069 kPa
Resonant Frequency ≥250 kHz ≥250 kHz
Rise Time (Reflected) ≤2 µ sec ≤2 µ sec
Low Frequency Response (-5 %) 0.5 Hz 0.5 Hz
Non-Linearity ≤1.0 % FS ≤1.0 % FS [ 1]
Environmental
Acceleration Sensitivity <0.002 psi/g <0.0014 kPa/(m/s²)
Temperature Range (Operating) -65 to +250 °F -54 to +121 °C
Temperature Coefficient of Sensitivity ≤0.10 %/°F ≤0.18 %/°C
Maximum Flash Temperature 3000 °F 1649 °C
Maximum Shock 20000 g pk 196133 m/s² pk
Hazardous Area Approval ATEX ATEX [ 7] [ 8] [ 9]
Hazardous Area Approval CSA (C-US) NRTL - Canadian Standards Association CSA (C-US) NRTL - Canadian Standards Association [ 3] [ 4] [ 5] [ 6]
Electrical
Output Polarity (Positive Pressure) Positive Positive
Discharge Time Constant (at room temp) ≥1.0 sec ≥1.0 sec
Excitation Voltage 20 to 28 VDC 20 to 28 VDC
Constant Current Excitation 2 to 20 mA 2 to 20 mA
Output Impedance <100 Ohm <100 Ohm
Output Bias Voltage 8 to 14 VDC 8 to 14 VDC
Electrical Isolation 100000000 Ohm 100000000 Ohm
Physical
Sensing Geometry Compression Compression
Sensing Element Quartz Quartz
Housing Material Stainless Steel Stainless Steel
Diaphragm 316L Stainless Steel 316L Stainless Steel [ 10]
Sealing Welded Hermetic Welded Hermetic
Electrical Connector 10-32 Coaxial Jack 10-32 Coaxial Jack
Weight 0.6 oz 17.0 gm
* All specifications are at room temperature unless otherwise specified
.




Specification Notes


[ 1] Zero-based, least-squares, straight line method.
[ 2] Due to high sensitivity, the static pressure should be applied and removed very slowly. Rate should prevent more than 10 Volt change in output until Output Bias Voltage returns to normal (approximately 15 times discharge time constant).
[ 3] AEx nA IIC T4, DIV2 CL1 GR A-D
[ 4] Ex nL IIC T4, DIV2 CL1 GR A-D
[ 5] AEx ia IIC T4, DIV1 CL1 GR A-D
[ 6] Ex ia IIC T4, DIV1 CL1 GR A-D
[ 7] Ex ia IIC T4.
[ 8] Ex nL IIC T4.
[ 9] Ex nA IIC T4.
[ 10] Diaphragm with ablative coating.
[ 11] See PCB Declaration of Conformance PS059 for details.