torkdisc® system, 16-bit telemetry system, 1,000 in-lb/83 ft-lb (113 n-m) rated capacity, 200% static overload protection, 15,000 rpm max., anodized aluminum

TORKDISC 1,000 LB-IN (113 NM)

Model 5302D-03A

Add to Quote
  • CE
  • IP

TORKDISC® System, 16-bit telemetry system, 1,000 in-lb/83 ft-lb (113 N-m) rated capacity, 200% static overload protection, 15,000 RPM Max., anodized aluminum

Cable Length Options: 24, 80, 112 and 176 feet


  • Measurement Range: 1000 in-lb (113 Nm)
  • Temperature Range: +32 to +185 °F (0 to +85 °C)
  • Torsional Stiffness: 2900000 in-lb/radian (327656 N-m/radian)
  • Overload Limit: 3300 in-lb (373 Nm)
  • Housing Material: Anodized Aluminum
  • Weight: 3.5 lb (1.6 kg)

Specification Notes

[1] Request Technical Note FTQ-STN5 regarding digital output signal.
[2] Extraneous load limits reflect the maximum axial load, lateral load, and bending moment that may be applied singularly without electrical or mechanical damage to the sensor.
[3] Where combined extraneous loads are applied, decrease loads proportionally.
[4] Request Application Note AP-1015 regarding the effects of extraneous loads on the torque sensor output.
[5] Output can be filtered via internal DIP switch (33, 55, 125, 250, 450 Hz).
[6] Root sum square of non-linearity, hysteresis, and non repeatability.
[7] Bolt joint slip torque is calculated assuming a coefficient of friction (µ) of 0.1 and that grade 8 socket head cap screws are used and tightened to 30% of yield.

English: SI:
Performance
Measurement Range (Full Scale Capacity) 1000 in-lb 113 Nm
Accuracy ±0.10 % FS ±0.10 % FS [6]
Voltage Output ±10 V ±10 V
Frequency Output 10 kHz ± 5 kHz 10 kHz ± 5 kHz
Digital Output QSPI QSPI [1]
Maximum Load (Axial) 250 lb 1.1 kN [2] [3] [4]
Maximum Load (Lateral) 250 lb 1.1 kN [2] [3] [4]
Maximum Moment 750 in-lb 85 Nm [2] [3] [4]
Frequency Range 2000 Hz 2000 Hz [5]
Environmental
Overload Limit (Bolt Joint Slip) 3300 in-lb 373 Nm [7]
Overload Limit (Failure) 4000 in-lb 452 Nm
Overload Limit (Safe) 3000 in-lb 339 Nm
Temperature Range (Operating) +32 to +185 °F 0 to +85 °C
Temperature Range (Compensated) +70 to +170 °F +21 to +77 °C
Temperature Effect on Output (within compensated range) 0.003 %FS/°F 0.0054 %FS/°C
Temperature Effect on Zero Balance (within compensated range) 0.003 %FS/°F 0.0054 %FS/°C
Electrical
Power Required (50 to 60 Hz) 90 to 240 VAC 90 to 240 VAC
Digital Resolution 16 Bit 16 Bit
Digital Sample Rate 26000 samples/sec 26000 samples/sec
Physical
Maximum Speed 15000 RPM 15000 RPM
Permissible Axial Float (rotor to stator) 0.25 in 6.4 mm
Permissible Radial Float (rotor to stator) 0.25 in 6.4 mm
Rotating Inertia (without adaptors) 0.056 in-lb/sec2 0.006 N-m/sec2
Torsional Stiffness 2900000 in-lb/radian 327656 N-m/radian
Torsional Angle (at Full Scale Capacity) 0.020 ° 0.020 °
Housing Material (Sensor) Anodized Aluminum Anodized Aluminum
Weight 3.5 lb 1.6 kg

* All specifications are at room temperature unless otherwise specified.

Accessories
Supplied
182-028A 25-pin(M) D-sub conn. (mating connector for 53xxC Series receiver outputs) 1
8314-06-24A 24-ft long black coaxial cable (RG58/U), BNC plug to TNC male plug 1