torkdisc® system, 16-bit telemetry system, 2,000 in-lb/167 ft-lb (226 n-m) rated capacity, 200% static overload protection, 15,000 rpm max., anodized aluminum

TORKDISC 2,000 LB-IN (226 NM)

Model 5302D-01A

Add to Quote
  • CE
  • IP

TORKDISC® System, 16-bit telemetry system, 2,000 in-lb/167 ft-lb (226 N-m) rated capacity, 200% static overload protection, 15,000 RPM Max., anodized aluminum

TORKDISC® System comes complete with receiver unit, 24 foot cable, and 12 VDC power supply.


Cable Length Options: 24, 80, 112 and 176 feet


    Specification Notes

    [1] Request Technical Note FTQ-STN5 regarding digital output signal.
    [2] Extraneous load limits reflect the maximum axial load, lateral load, and bending moment that may be applied singularly without electrical or mechanical damage to the sensor.
    [3] Where combined extraneous loads are applied, decrease loads proportionally.
    [4] Root sum square of non-linearity, hysteresis, and non repeatability.
    [5] Selectable High Pass cutoff frequencies of 5, 10, 20, 200 and 500 Hz.
    [6] Selectable Low Pass cutoff frequencies of 10,000, 5000, 2500, 1200, 625 and 313 Hz.
    [7] Bolt joint slip torque is calculated assuming a coefficient of friction (µ) of 0.1 and that grade 8 socket head cap screws are used and tightened to 30% of yield.
    [8] Supplied with universal AC power adaptor.
    [9] See PCB Declaration of Conformance PS069 for details.

    English: SI:
    Performance
    Measurement Range (Full Scale Capacity) 2000 in-lb 226 Nm
    Accuracy ±0.10 % FS ±0.10 % FS [4]
    Filter Type (High Pass) 2-pole Butterworth 2-pole Butterworth [5] [6]
    Filter Type (Low Pass - Anti Alias) 8-pole Elliptical 8-pole Elliptical
    Gain (Channel A) 1-16 dB 1-16 dB
    Gain (Channel B) 0.3-1.3 dB 0.3-1.3 dB
    Voltage Output (channel B - DC coupled) ±10 V ±10 V
    Voltage Output (channel A - AC coupled) ±10 V ±10 V
    Digital Output QSPI QSPI [1]
    Maximum Load (Axial) 500 lb 2.2 kN [2] [3]
    Maximum Load (Lateral) 500 lb 2.2 kN [2] [3]
    Maximum Moment 1500 in-lb 169 Nm [2] [3]
    Accuracy ±10 % FS ±10 % FS
    Frequency Range (-3 dB) 0 to 8500 Hz 0 to 8500 Hz
    Environmental
    Overload Limit (Bolt Joint Slip) 3300 in-lb 373 Nm [7]
    Overload Limit (Failure) 8000 in-lb 904 Nm
    Overload Limit (Safe) 6000 in-lb 678 Nm
    Temperature Range (Rotor/Stator - Operating) +32 to +185 °F 0 to +85 °C
    Temperature Range (Rotor - Compensated) +70 to +170 °F +21 to +77 °C
    Temperature Range (Receiver - Operating) 0 to +122 °F -17.7 to 50 °C
    Temperature Effect on Output (System - within compensated range) 0.002 %FS/°F 0.0036 %FS/°C
    Temperature Effect on Zero Balance (System - within compensated range) 0.002 %FS/°F 0.0036 %FS/°C
    Position Sensitivity (180° rotation of sensor) ≤0.1 % FS ≤0.1 % FS
    Electrical
    Power Required 9 to 18 VDC 9 to 18 VDC [8]
    Digital Resolution 16 Bit 16 Bit
    Digital Sample Rate 26484 samples/sec 26484 samples/sec
    Analog Resolution (based on ±10 V FSO and 16-bit resolution) 0.31 mV 0.31 mV
    Physical
    Maximum Speed 15000 RPM 15000 RPM
    Permissible Axial Float (rotor to stator) 0.25 in 6.4 mm
    Permissible Radial Float (rotor to stator) 0.25 in 6.4 mm
    Rotating Inertia (without adaptors) 0.142 lb-ft² 0.006 kg-m²
    Dynamic Balance per ISO G 2.5 per ISO G 2.5
    Torsional Stiffness 5800000 in-lb/radian 655312 N-m/radian
    Torsional Angle (at Full Scale Capacity) 0.020 ° 0.020 °
    Housing Material (Sensor) Anodized Aluminum Anodized Aluminum
    Weight (rotor/sensor) 3.5 lb 1.6 kg

    * All specifications are at room temperature unless otherwise specified.

    Accessories
    Supplied
    012AC024AT 1
    182-028A 25-pin(M) D-sub conn. (mating connector for 53xxC Series receiver outputs) 1
    M0003978 1