Model: 102A10

$2,095.00 USD
(Pricing valid in US only)


Call for lead time

Cryogenic ICP® pressure sensor, 100 psi, 50 mV/psi, 3/8-24 mtg thd, ground isolated

  • Measurement Range: 100 psi (690 kPa)
  • Sensitivity: (±15%) 50 mV/psi (7.25 mV/kPa)
  • Low Frequency Response: (-5%) 0.50 Hz
  • Resonant Frequency: >=250 kHz (>=250 kHz)
  • Electrical Connector: 10-32 Coaxial Jack
  • Weight: 0.388 oz (11.00 gm)

Add this product to my product comparison
Compare selected models ()

 English:SI: 
Performance
Measurement Range (for ±5V output)100 psi690 kPa 
Useful Overrange (for ± 10V output)200 psi1380 kPa[4] 
Sensitivity (±15 %)50 mV/psi7.25 mV/kPa 
Maximum Pressure (step)1000 psi6900 kPa 
Maximum Pressure (Total)15 kpsi103425 kPa[3] 
Resolution2 mpsi0.014 kPa[2] 
Resonant Frequency≥250 kHz≥250 kHz 
Rise Time (Reflected)≤2.0 µ sec≤2.0 µ sec 
Low Frequency Response (-5 %)0.50 Hz0.50 Hz 
Non-Linearity≤1.0 % FS≤1.0 % FS[1] 
Environmental
Acceleration Sensitivity≤0.002 psi/g≤0.0014 kPa/(m/s²) 
Temperature Range (Operating)-320 to +212 °F-196 to +100 °C 
Temperature Coefficient of Sensitivity≤0.06 %/°F≤0.108 %/°C 
Maximum Flash Temperature3000 °F1649 °C 
Maximum Vibration2000 g pk19613 m/s² pk 
Maximum Shock20000 g pk196133 m/s² pk 
Electrical
Output Polarity (Positive Pressure)PositivePositive 
Discharge Time Constant (at room temp)≥1.0 sec≥1.0 sec 
Excitation Voltage20 to 30 VDC20 to 30 VDC 
Constant Current Excitation2 to 20 mA2 to 20 mA 
Output Impedance<100 Ohm<100 Ohm 
Output Bias Voltage8 to 14 VDC8 to 14 VDC 
Physical
Sensing ElementQuartzQuartz 
Housing Material304L/316L Stainless Steel304L/316L Stainless Steel 
Thread Adaptor Material316L Stainless Steel316L Stainless Steel 
Diaphragm316L Stainless Steel316L Stainless Steel 
SealingWelded HermeticWelded Hermetic 
Electrical Connector10-32 Coaxial Jack10-32 Coaxial Jack 
Weight0.388 oz11.00 gm 

All specifications are at room temperature unless otherwise specified.


CE

Product Notes
[1] Zero-based, least-squares, straight line method.
[2] Typical.
[3] Due to high sensitivity, the static pressure should be applied and removed very slowly. Rate should prevent more than 10 Volt change in output until Output Bias Voltage returns to normal (approximately 15 times discharge time constant).
[4] Excitation voltage >=28 volts required.
[5] See PCB Declaration of Conformance PS023 for details.
Accessories:
Supplied
065A44Seal ring 0.435" OD x 0.377" ID x 0.030" thk Cu(3)
Optional Versions:
(M) Metric Mount
Accessories:
    065A34Seal ring 0.435" OD x 0.397" ID x 0.030" Cu(3)
Product Documents
Additional Downloads None Listed